silikonmade.blogg.se - Setup lyn for mac 2011 as default

#Setup lyn for mac 2011 as default how to
#Setup lyn for mac 2011 as default install
#Setup lyn for mac 2011 as default download

Microsoft recommends this setting to be 200, but this isn't long enough for iOS clients.

Note: This is needed to prevent the Lync Web Apps server from timing out unexpectedly.

Change the Time-out (seconds) from 30 seconds to 600 and click Apply.

Select the same Server Farm object and double click on Proxy.

Uncheck Enable disk cache and click Apply.

Select a Server Farm and double click on Caching.

This is needed to communicate properly with the WAC server.Ĭonfigure IIS Caching, Proxy Timeouts, and Routing Rulesįor each of the server farms we created, repeat the following steps:

For your Lync Web Apps server ( lyncwac), continue repeat steps 1-6, however ensure you use ports 80 and 443 instead of 80.

Repeat steps 1-6 for dialin, meet, and lyncdiscover.

Change the httpPort to 8080 and httpsPort to 4443 and click Add.

Enter the Server address (same as farm name before), click Advanced Settings., expand applicationRequestRouting.

For the sake of this tutorial, I am going to use lync first. This can be lync, dialin, meet, etc, order will not matter.

Note: We will end up creating farm names for each externally published URL.

Enter in the Server farm name and click Next.

Select Server Farms and then click on Create Server Farm.

Select https, and choose your SSL certificate you imported in the previous step, click OK.

Expand your server, expand Sites, select Default Web Site, select Bindings.

This SSL certificate should be the UCC certificate that allows for SAN addresses such aslync, meet, dialin, lyncdiscover, etc. Note: Generation of this certificate is outside the scope of this tutorial.Generate or Import your SSL Certificate trusted by a public CA (VeriSign, GoDaddy, etc.).Select your server and double click on Server Certificates.Open up Internet Information Services (IIS) Manager.If you are running version 2.5, you will see 2 items needed for install. Note: The cart for the v3.0 installer is shown above.Run the ARRv3_0.exe application as an administrator.

Installing IIS Application Request Routing (ARR) 3

#Setup lyn for mac 2011 as default install

Install IIS for Server 2012 and Server 2012 R2 Instructions can be found here: (arr)/install-application-request-routing-version-2.Install Application Request Routing version 2.

#Setup lyn for mac 2011 as default how to

Ensure you have IIS v7.X installed instructions on how to do this can be found here:.

#Setup lyn for mac 2011 as default download

Download (don't install yet) Hotfix for Microsoft Application Request Routing Version 2.5 for IIS7 (KB 2732764) (圆4).Download IIS Application Request Routing (ARR):.I have attached the links on how to get Server 2008 and Server 2008 R2 prepped, so you can continue the tutorial once the IIS Application Request Routing extension has been installed. This tutorial will go over installation instructions from start to finish for Server 2012 and Server 2012 R2. Side note, much of this guide is largely based on an older technet article published here, which has some additional fine details on how exactly IIS is working to proxy the requests: Per Microsoft's documentation, we can use IIS with an additional extension called Application Request Routing to achieve this task: ĭetails on the IIS Application and Request Routing extension can be found here: In turn, a few tutorials have popped up on how to achieve this using Apache and IIS, but there wasn't an official recommendation on what to use until Server 2012 was released. The original method for deploying a reverse proxy was to use Microsoft's product ForeFront TMG (Threat Management Gateway), however shortly after the release of Lync Server 2013, TMG was discontinued. In this tutorial we will go over deploying a reverse proxy for Lync Server 2013.